Serpent now offers the Cobra GT-E also in a Ready To Race, to make this superb car even more attractive to a broader customer base, so also Hobby racers can now join in for the action. This RTR version includes it all.
Topquality components packed in a Ready-to-race package, the best start a Hobby-driver can make.
High end racing chassis with top quality parts, impressive 2.4 GHz transmitter, Waterproof electronic speedcontroller with smal footprint, which fits the Cobra GT Ey holder like a glove combined with a strong 2450KV brushless motor with lots of torque.
Transmitter and receiver
The DragonRC DTS-3 2.4GHZ pistol type transmitter
The small and light receiver is fitted inside the radiobox of the car.
The electronic speedcontroller is a fully Waterproof 120A unit from DragonRC with a small footprint which fits the Cobra like a glove. The new modern design is very small and attractive looking. Topquality soft silicone covered cables.
The DragonRC brusless sensorless motor is a strong 2450kv unit which gives lots of torque and amazing topspeed. , and is anodised in same bronze color as the other alu parts of the car.
Chassisplate in 3mm 7075 T6 aluminium. Kick-up angle on front for stabile landings. Countersunk holes. Slots to locate the front and rear suspension mounts precisely. Angled sides to increase stiffness.
Large foam bumper, which is kept in place by a upper and lower nylon bumperplate.
Composite stiffner front and rear, to give extra stiffness, but still allow some flex as needed.
Central radio / servo mount
Composite compact radiobox which offers good space for the steering servo and the receiver.
Battery-cases / side-guards
The main eyecatchers are the extremely low laydown longtudinal placed battery-packs at each side of the car, being part of the side-guards, securely fastened with a fliptop-lid, for easy and fast battery changes. The weight low in the car and in the right position, well balanced. The Lipo holders comply with ROAR legal packs / dimensions.
The motor is placed in the most optimal position in the car, keeping motor-forces and transmission parts / alignment in mind. Only one-screw is needed to secure the BL motor, in the nicely designed durable machined aluminium motormount. Space for additional motor-cooling available as needed.
The space for the motor allows a maximum motor-length of 70mm, which covers most widely used motors ( except for the truggy / monstertruck motors).
Composite steeringblocks combined with 10 dgr C-hubs for precise steering. Spring steel wheel-axles with large size bearings and larger inner with precision threaded aluminum wheel-hubs with offset . Flanged wheel nuts to guarantee that you will not loose a wheel nut in a race.
Durable oversized lower suspension arms in strong composite nylon. On the lower side the special shaped downstops screws are mounted. The lower shock-mounting pins are secured with a small grubscrew from the bottom.
Front anti-roll bar
The ballraced front anti-roll bar system, consist of a spring steel bend wire, which is guided through the diff-cases and runs in ballraced steel adaptors. The wire is linked to the lower suspension arm, with a captured adjustable threaded pivotball, for very precise and low friction operation and easy tuning.
Shocktower and bodymounts front
4.0mm thick aluminium anodised shocktower with 2 upper positioning holes for the shocks and and 3 holes for roll-center positions. Strong, in height adjustable bodymounts with wide top-section to seat the body well.
Angled steering system / servo saver
The bell cranks are angled to reduce the angle of difference between the total caster and steering plane. Therefore you will have less bump steer and a truer steering Ackerman through the entire range of suspension
With the design of the steering bell cranks when changing the Ackermann you will not need to adjust your steering tie rods. You simply will only need to adjust your end points on your radio..
Rear suspension arms
Durable longer oversized lower suspension arms in strong composite nylon. On the lower side the special downstops screws are mounted. The lower shock-mounting pins are secured with a small grubscrew from the bottom.
Rear uprights assembly
Composite uprights with 3 upper roll-center positions. Strong steel track-rods with L/R threading and strong balljoints to pre-set camber. Hard steel wheel-axles with large size bearings and larger inner ones with precision threaded aluminum wheel-hubs with offset. Flanged wheel nuts to guarantee that you will not loose a wheel nut in a race.
Rear anti-roll bar
The ballraced front anti-roll bar system, consist of a spring steel bend wire, which is guided through the rear wingmount and runs in ballraced steel adaptors. The wire is linked to the lower suspension arm, with a captured adjustable threaded pivotball, for very precise and low friction operation.
4.5mm thick aluminium shocktower, integrated into the rear section for extra stiffness, with 2 upper positioning holes for the shocks and 3 holes for roll-center positions.
Wingmount and bodymounts rear
Polycarbonate rear low aero wing. Central rear bodymount with the rear bodypost, which are adjustable in height easily .
Captured pivot pins and balls and bolted hinge pins
All spring-steel hinge pins are either captured or bolted in place and made in spring-steel quality. This relieves stress on the hinge pin when adjusting the kick up, or anti squat. Your pin is free to rotate to any angle without binding.
Shockabsorbers RCM big-bore 16mm
Anodised aluminium shockbodies with durable 4mm shock-rods. Pre-load adjuster clips for ride height setting. Shocks use large diameter membrames and large diameter o-rings and bushings to create a supersmooth and leak-proof package. Large diameter pistons are held in place by a nut on the polished shock-rods tops. Open type spring retainer to let dirt out easy.
RCM shock springs
Colorcoded progressive race shock springs are supplied for the 1st standard set-up and all springs are grinded flat top and bottom, and checked individually for tension and length and are matched.
Very compact gear differentials with very smooth metal sintered gears, and steel shaft. Perfect sealing case with special gasket and o-rings. Very light and durable outdrive cups in spring-steel. Hardened spring-steel diff-coupler 13T with connector running in 2 oversized bearings The Cobra-GT-E uses a 13T / 44T combo gearing. 46T central diff gear. This drive ratio will provide amazing acceleration combined with the low vehicle weight.
Front and rear drive
The front has captured driveshafts using a CVD system. The rear has durable black steel driveshafts with hard steel pins.
Hard black steel transmission parts
The front and rear strong hard black steel cardan shafts connect the differentials .
Serpent superlow Cobra GT body, fully pre-painted in a very attractive design and pre-cut too. The very low body has excellent handling and downforce
Tyres / wheels
The Cobra is fitted with premounted DragonRC GT racing tyres. The tyres are glued on durable but flexible DragonRC race-wheels with cell-foam inserts. A super-package for excellent grip on the most common surfaces.
Oils and grease
Top-quality silicone shock-oil, silicone diff oil and some grease is used to meet the standard set-up.
Manual and set-up
Full color user manual with easy to follow steps, exploded views for easy spares ordering. A seperate manual for the transmitter and the speed controller is included.
Black and white promo body-decals ; Serpent generic and Cobra GT ones.
The RTR kit is packed in a colorfull large strong packing box with protection for car and transmitter.
Serpent Cobra 811 Be Buggy RTR EP 1/8 4wd
- race ready high performance electric GT ⅛
- expert pre-assembled and pre-set
- 4wd with cardanshafts, 3 compact ,durable geardiffs, super-easy machined alumiunium motormount, superlow longtudinal batteryboxes, compact speedo-servo mount, unique angled steeringsystem, 16mm bigbore shocks, ballraced anti-roll bars FR and RR, 7075 T6 alu shocktower FR and RR, durable suspension and transmission parts, captured supension pins, the works !!
- Dragon-RC pistol type transmitter 2.4 GHz
- Dragon-RC 120A waterproof speedcontroller
- Dragon-RC powerfull 2450kv brushless sensorless motor
- Dragon-RC 10.5kg strong servo with metal gears
- Dragon-RC high grip premounted GT racetyres and wheels
- prepainted and precut ultra low GT bodyshell and large rear aero-wing
- full color user manual and decalset included
Service and Support
The Serpent distributor, dealer or agent is your source for more info, but also the Serpent website and the member section and the Youtube channel provides lots of information.
Needed to complete the car:
- 4 x AA batteries for the transmitter
- 2 x Lipo hard-packs 3800 mA or more
- (charging equipment/ powersupply)
For rc accessories:
Product Type:Electric cars > 1/8 onroad:
Class:1/8 scale 4wd GT -e Ready to race
Purpose:clublevel racing and parking lots
Drivetrain:cardan shafts, 3 gear diffs
Shocks:RCM shocks with membrame
Manual:full color RTR manual, speedo manual, radio manual
Included:body, radio equipment, speedo, motor , tyres-wheels
Not included:batteries, charger, tools