Serpent Natrix 748 1/10 scale 4wd gaspowered 200mm car 4wd, belt-drive, gear-differentials front and rear, Centax TM clutch, 2-speed gearbox, 75cc tank, chassis 7075-T6, carbon radioplate and shocktowers, RCM-SS shocks, ball-raced anti-roll bars, fully adjustable.
Serpent NATRIX 748
1/10 scale gaspowered 200mm racecar
Key new features
Michael Salven as chief designer, has worked closely together with key team drivers Green, Greiner, Morganti, Mazzeo and the Sahahsi Bro’s to create the next level in 1/10 scale gas powered racing.
- The innovative steeringblock system, well proven on the WC winning Viper 977, is fully adjustable, allow for a leading, neutral or trailing position and allow mounting of the optional carbon aero disks
- A new fueltank is designed, which sits even lower in the car as before, and is long and narrow
- The lay-down servo’s are both seated in one composite holder, as close as possible to the centerline of the car, creating a better overall balance and enabling better rotation. The gas-throttle linkages are similar to the unit used on the Viper 977
- A nice small and light receiver box is made, which seats very close to the radio-tray and as much inboard as possible . On the radioplate a small holder is fitted to accept the plugs of the battery, to act as on/off “switch”.
- The ballraced rear anti-roll bar is optimised position wise.
- The alumium rear brake and 2-speed shaft holders, which also hold the rear anti-roll bar are lighter
- The new chassisplate allows the engine to be mounted more to the back as before, resulting in a better overall balance. Therefor the rear and side belt are new too.
- The rear uprights are modified to also accept the optional carbon aero disks
- The radioplate sits extremely low in the car, and it fitted in the rear with a new type ballraced flexsystem, which an be used or locked in seconds.
- The lower radiotray made a new steering / servo saver assembly necessary, again with adjustable ackermann inserts as before.
- On the front end the bumper is a larger low mounted unit with the carbon top-plate.
- Overall the NATRIX car is lighter than 747 before, as also most aluminium parts have been redesigned to loose weight.
Serpent 748 ; details
Symmetrical chassisplate for even flex and torsion, in 7075 T6 aluminium, anodised and laser engraved. Chamfered edges for more ground clearance when cornering and countersunk holes. Central slots to mount weight, which can slide into the right position and then secured.
The 2mm carbon fibre radioplate has multiple functions. It holds the fueltank in place which is mounted on 3 alu posts in rubber. On the right hand side the receiver mounts to a nicely shaped carbon fibre plate that connects to the radiotray, sqeezed in right between belt and tank. The radioplate sits again lower on the car , for lower center of gravity.
Central Flex system
The rear section of the radioplate incorporates a nice flex-control system. It consists of 2 machined aluminium parts. The lower one connects to the radioplate supports an the upper one with screws to the upper alu plate and radioplate. You can either run the 748 rigid with flex . The optional ball-bearings and screws are sold seperate. Testing has shown that flex in the center rear of the car has the most effect and reacts most predictable as wel.
748 servo holder
A new composite servo holder is designed to have both servo closer to the center line of the car and as low as possible. The 2 lay-down servo’s are seated very close together and mount in a very efficent and easy way. The holder mounts to the radio-tray.
The throttle / brake linkage is same style as used on the 977 1/8 car. A pivot-lever system with an ingenius ball-cup system to the guide the wire and have almost friction free action.
748 receiver box
The new composite receiver box is small but holds and protects the most common modern receivers easily. The antenna mounts to the top. The box is securely fastened to the radioplate with a nylon bracket . The box has been moved as much to the inside as possible. On the radioplate a small holder is fitted to accept the plugs of the battery, to act as on/off “switch”.
Carbon fibre battery-holder positioned between the tank and pipe, for the best weight balance. The battery is easy to strap down with tape to the bracket. Spacers can be used to mount the battery higher or lower depending on the battery you plan to use.
Lower and longer durable 75ccm nylon fueltank with transparent material to easy see fuel-content. Large springloaded quick-fill cap with seal with large tank opening for fast and easy refills. The bronze sintered filter will keep fuel clean and make sure tank will empty till last drop if needed. Fueltank sits very low in the car for low center of gravity. Fueltank is mounted with clips on 3 alu posts with rubber buffers.
SuperShort RCM shocks
Coated threaded shockbodies in high quality aluminium. Supersmooth o-ring / bushing package, to guide and seal the spring-steel piston rods. Precision moulded pistons included in 3 types. Threaded pre-load shocknuts in alu with o-ring inside. Light but strong nylon spring-cups. Selected, matched and paired shockabsorber springs with color coding.
Front bumper and bodymount
Front bumper with aerodynamic effects and excellent protection. Some parts of the lower bumper can be cut open to create more steering. Medium or small foam bumper pad scan still be fitted as optional. The upper carbon fibre bodyplate mounts to the front bumper with alu post and secures the front bdyposts
Superlow 3.0mm carbon fibre shocktowers with 3 positions for upper shockmounting. In the centre you can mount the 3rd bodypost as needed.
A compact and superlight structure of topquality aluminium parts consist of top-brackets, L and R equal bearing brackets, lower suspension bracket front. The open style design allows for very fast parts exchange as needed, like belt, diff or anti-roll bar.
Strong long double A-arm suspension with aluminium pivotballs, which pivot in light nylon cups. Hard type composite arms. The arms pivot on the inside on springsteel pins. The pivot-inserts are used to change rollcenter. Small grubscrews mount in the upper bracket to control downstop. Easy to access and change ride height, front width, toe-in, caster and camber.
Very strong composite steeringblocks with 2 ackermann positions, L and R use the same . The steeringblocks feature inserts, which allow to change the kingpin inclination to a leading or trailing position. The steeringblocks also allow use of the optional carbon fibre aero disks to be mounted for less flex and a more direct steering feel.
Wheelaxles / cvd
The spring-steel wheelaxles are seated in high speed bearings. The light and durable spring-steel cvd’s bring all the power to the front wheels. Wheels are mounted to orange anodised high grade aluminium hex-adaptors using flanged wheelnuts.
Anti-roll bar front
The ballraced wire type anti-rollbar in the front is really easy to access and change for other type or thickness as needed. The anti-roll bar is linked to the lower a-arms with a unique pivotball/cup system, which provides direct and smooth operation and is easy to set and adjust.
Servo-saver / steering
The new lowered centraly mounted steel servo-saver post fits the spring-loaded ballraced servo-saver system and steering. The inserts allow 2 ackermann settings. Due to the open design the linkages with L/R threading can be reached easily. The whole system allows for very precise steering and minimum bumpsteer.
Middle shaft holder
Machined 2 piece aluminium middle shaft holder, which securely holds the spring steel middle shaft, and doubles up as holder of the pipe-mount.
Very rigid but open rear end design with a composition of machined alu brackets, allowing for easy maintenance. The differential brackets, L and R equal, are toothed and seat the excentric bearing holder, which allow for setting belttension. Its very quick and easy to mount a differential and or replace a belt. The machined aluminium lower suspension brackets have roll-center inserts with 3 positions to choose from. The rear bracket is the narrow V1 version.
The 2-speed gearbox shaft holders, double up as anti-roll mounts, and brake system basis. All topquality machined parts with anodising and laser-engraving.
the low mounted brake system with superlight disk allows for smooth and even braking, and the open system avoids overheating. The ball-raced excenter and lever gives a very smooth and direct brake-feeling.
Rear carbon shocktower and camber bracket
The low 3.0mm carbon shocktower has 3 upper mounting position for the shocks and it mounts the body-posts. The camber bracket offers 8 positions to choose from, 4 inner and 4 out holes. The shocktower is prepared to mount the extra body-protectors, which are optional.
The Hard lower rear composite arms together with the updated uprights create a wider set-up sweet-spot with more grip and more steering. The upper camber rods connect to the carbon camber bracket with 8 mounting positions for roll-center and the camber rod is easy to access and has L/R threading for fast changes. The aluminium pivotball system allows for fast changes in width and toe-in. On the lower inside the wishbone pivots on springsteel pins, which seat with roll-center inserts in the anodised alu suspension brackets.
Lower rear wishbones
The hard composite lower wishbones feature a mounting position for the anti-roll bar linkage which moves the link position more outside. Its also offers a mounting position for an optional carbon shock-mount bracket, to move the lower shockmount position further out, but for the default set-up its not needed. By placing the lower shock further out, you will get even more steering .
Uprights / wheel-axles
Durable medium type composite uprights, which seat the wheel-axles bearings. The upright offers the mounting position for the steel camber-rod with L/R threading. Rolll center chnages can be made on top of the upright with shims. The upright can be mounted with the optional carbon fibre aero disks for more rear grip and straight line stability.
Wheelaxles and driveshaft
The durable spring steel wheelaxles combined with spring steel driveshafts bring the power from the gear-diff to the wheels. Wheels are fitted on high grade anodised alu wheelhex adaptors and secured with flanged wheelnuts.
Anti-roll bar rear
The ballraced wire type anti-rollbar in the rear is really easy to access from the top and change for other type or thickness as needed. The anti-roll bar is linked to the lower a-arms with a spring-steel rod.
Compact, durable and light gear differentials. Pecision moulded steel gears. The very durable and light spring steel lightened diff-adaptors connect to the driveshafts. Front and rear geardifferential are same, just different pullies.
Spring steel, light and very durable CVD’s used in the front. Precision mounted hard steel pins
Spring steel, light and very durable dogbones used in the rear. Precision mounted hard steel pins
Precision moulded super-true pullies, which feature holed sidewalls to let debris move out easier. Light and durable.
Low friction Kevlar reinforced belts with fine pitch. Longlasting and smooth.
Ball raced belt-tensioner, machined from aluminium and can mount on top or below the radioplate.
The well proven SL6 gearbox is standard in the 748. Light and compact, with very low rotating mass. Durable and longlasting gears. High quality bearings. Very grippy springloaded 2-speed shoes, easy to set.
True Motion Centax clutch
Serpent invented the Centax clutch in the mid 90-ties, and all brands followed it. Small improvements are found to make the original system even better. The True Motion Centax has a flat flywheel, and the taper part on the pressure plate. This allows the flyweights to work even better. The hard anodised aluminium flywheel has 4 holes to have easy access to keep the flywheel in position when setting the pre-tension. The flyweights are made of topquality teflon and feature an additional hole to use grubscrews to make them heavier. The red friction clutch shoe is very grippy, and works excellent with the steel clutch housing. The hard anodised gears screw onto the threaded steel bell.
The light machined and anodised engine mounts perfectly seats the engine, well alligned with the gearbox. Small adjustment can be made to move the engine closer to the gearbox.
Manual / set-up sheet
The 748 comes with a full color assembly manual, with easy to follow assembly steps. The manual also includes exploded views section showing all part numbers, and a full parts-list, showing also all optionals. The kit includes a default and blank set-up sheet. Editable sheets are in the Serpent website.
The 748 includes one sheet with Serpent generic logo’s and one with 748 logo’s. Decals are very thin material and come pre-cut.
The 748 comes in a strong, small carton box with nice graphics. The packing of the bags follows the steps in the manual.
Designed by World and European Champion Michael Salven
Product 804007 Serpent Natrix 748 1/10 200mm
Product-description Serpent’s new 200mm 1/10 4wd onroad racer.
4wd drive, fully adjustable suspension, 2-speed gearbox, Centax TM clutch, geardiffs FR and RR, belt-driven.