> 1/8 · Formula · 1/8 offroad · 1/10 200mm · 1/10 235mm

> Cobra 811 Truggy TE 1/8 (#600035)

> Description · News (30) · Specifications · Images (60) · Downloads (3) · Spares (201) · Optionals (113) · Setups (22)

Brand:
Serpent

Product Type:
Gas Cars > 1/8 offroad

Serpent Cobra Truggy, version TE, gaspowered 1/8 scale 4wd high end competition version. Kit version. New version features new diff-couplers combined with larger bearings, and larger bearings in the steeringblocks and uprights, all to increase durability even more. 4wd gaspowered version, based on the sucessfull Cobra Buggy. The ultimate competition racing truggy, for high end competition use. Designed by Serpent designer/racer Billy Easton, USA.

Related products


> Description

Serpent Cobra 811 Truggy TE 1/8 GP

Introduction

This new development for  Cobra Truggy is mainly created to further improve durability and   features  improved differential  couplers  front and rear and larger bearings for same, and also larger bearings in the steeringblocks and  up-rights.  The new coupler in the front also requires a new central front cardan shaft.  The new uprights fit the new wheel-axles which feature rubber dustboots , combined with a  new length rear cvd driveshafts. The steeringblocks are same as from the Cobra buggy, and those had the larger bearings already while ago and are in use on many Cobra truggies too.

Chassisplate   
Chassisplate in  3mm  7075 T6 aluminium , with machined pockets to create flex  make lighter.  Kick-up angle on front  for stabile landings.  Countersunk holes.   Slots to locate the  front and rear suspension mounts precisely.  Angled sides to increase stiffness.  Laser engraved Cobra T logo.   
   
Bumper    
Aligned with chassis  kick-up for precise landings and to protect front suspension holder and anti-roll bar.
   
Chassis stiffners   
Composite  stiffner front and rear, to give extra stiffness, but still allow some flex as needed.   
   
Central radio / servo mount   
Composite radiobox which offers good space for the  steering and throttle -servo, the receiver and  rx battery.   The whole assembly including linkages can be taken off easily and fast in one go, when cleaning the car, or doing maintenance. One extra post is added close to the servo for stability.    
Servo arms and linkages   
The servo arms have a splined insert to have the right fit per brand. The linkages run very clean and tight and are easy to access to modify settings.   
   
Suspension brackets   
Beautifully machined  7065 T6  suspension brackets in anodized, laser angraved.  Precision fit for the nylon roll center inserts  and pivot balls / pins.    
   
Steeringblocks assembly    
Composite steeringblocks combined with 10 dgr C-hubs  for precise steering.  Spring steel wheel-axles with large size bearings    and larger inner     with precision threaded aluminum wheel-hubs with offset  . Flanged and serrated wheel nuts to guarantee that you will not loose a wheel nut in a race.
   
Front suspension   
Durable oversized  lower suspension arms in strong composite nylon. On the lower side the special shaped downstops screws are mounted. The lower shock-mounting pins are secured with a small grubscrew from the bottom.    
   
Front anti-roll bar   
The ballraced front anti-roll bar  system, consist of a spring steel bend wire, which is guided through the diff-cases and runs in ballraced steel adaptors.  The wire is linked to the lower suspension arm, with a captured adjustable threaded pivotball, for very precise and low friction  operation and easy tuning.   
   
Shocktower and bodymounts front   
4.5mm thick carbon shocktower with 5 upper positioning holes for the shocks and and 6 holes for roll-center positions.  1 centrally located adjustable bodymount , and 2 forward mounted adjustable bodymounts, all with flip-tops.    
   
Angled steering system / servo saver   
The bell cranks are angled to reduce the angle of difference between the total caster and steering plane. Therefore you will have less bump steer and a truer steering Ackerman through the entire range of suspension   
   
Ackerman plates   
With the design of the steering bell cranks when changing the Ackerman you will not need to adjust your steering tie rods. You simply will only need to adjust your end points on your radio..    
   
Rear suspension arms   
Durable long oversized  lower suspension arms in strong composite nylon. On the lower side the special downstops screws are mounted. The lower shock-mounting pins are secured with a small grubscrew from the bottom.    

Mud-guards
Mud guards  mount to the lower suspension arms, and will keep dirt away from your anti-roll bars transmission and wheels.
   
Rear  uprights  assembly   
Composite uprights with 3 upper roll-center positions. Strong steel track-rods with L/R threading and strong balljoints  to pre-set camber.  Spring steel wheel-axles with large size bearings   and larger inner   ones  with precision threaded aluminum wheel-hubs with offset  . Rubber dustcovers in the rear to protect the cvd system and keep the lubrication inside. Flanged and serrated wheel nuts to guarantee that you will not loose a wheel nut in a race.   

Rear anti-roll bar   
The ballraced front anti-roll bar  system, consist of a spring steel bend wire, which is guided through the diff-cases and runs in ballraced steel adaptors.  The wire is linked to the lower suspension arm, with a captured adjustable threaded pivotball, for very precise and low friction  operation.   
   
Shocktower rear    
4.5mm thick carbon shocktower, integrated into the rear section for extra stiffness,  with 5 upper positioning holes for the shocks and 6 holes for roll-center positions.    
   
Wingmount and bodymounts rear   
Composite rear wing, with strong nylon adjustable rear bodymounts on wide body-support bridge located far enough to the rear, to support the bodies in best way.    
   
Captured pivot pins and balls and bolted hinge pins    
All spring-steel hinge pins are either captured or bolted in place and made in spring-steel quality. This insures your chances to finish an hour long main event, while battling for the lead.  This relieves stress on the hinge pin when adjusting the kick up, or anti squat. Your pin is free to rotate to any angle without binding.   
   
Shockabsorbers big-bore 16mm   
Hard Teflon coated threaded  shockbodies with 4mm shock-rods.  Hard anodized aluminium screw on shock-tops with Serpent laser engraving.   Pre-load adjusters with o-rings inside.  Shocks use  large diameter membrames and large diameter o-rings  and bushings to create a  supersmooth  and leak-proof package.  Large diameter pistons are held in place by a nut on the polished shock-rods tops. Open type spring retainer to let dirt out easy.  The shock-shafts are protected by rubber boots.   
   
RCM shock springs   
Short type colorcoded shock springs are supplied for the 1st standard set-up  Springs are grinded flat top and bottom, and checked individually for tension and length.     
     
Compact geardifferentials   
Very compact gear differentials with very smooth metal sintered gears, and steel shaft. Perfect sealing case with special gasket and o-rings.  Very light and durable outdrive cups in spring-steel.   Hardened spring-steel diff-coupler 10T with connector running in 2 oversized bearings .  Drive ratio 4.3:1. This drive ratio will provide amazing acceleration combined with the low vehicle weight. It is a sure win, to help improve fuel mileage
   
Front and rear cvd-sets   
Both front and rear captured  driveshafts are being used with CVD system.  Durable yet light  spring steel engraved driveshafts with hard steel pins.   
   
Spring steel transmission parts   
The front and rear thin but strong spring steel cardan shafts connect the differentials .     
   
Throttle and brake lever ball cups
Helps provide consistent pulling on the brake lever or carburetor if you do not have the linkage perfectly aligned.

Piston Braking system
Provides more stopping power than you could have ever imagined before with a whole lot less servo power. Also is fully adjustable with 3 types of pistons,  solid, O ring type,  spring type.  In turn you can adjust your bias or braking feel to your liking in more ways than ever before.

Fiber Glass disc brakes
Fiber Glass brake disks with oversized front disk.

Brake plate springs
Will keep the plates spread open to insure un-wanted dragging of the brake discs.

Racing clutch 4 - shoe
Allows you to mix and match shoe materials evenly in pairs. Also provides more surface area contact to insure the engagement.  4 carbon shaped shoes are standard ( alu ones optional).

Coil exhaust wire and alu mount
Helps aid in the front to back movement of the pipe when chassis flex occurs. Helps prevent damage to your exhaust gaskets.

Engine mount    
Machined 7075 T6 aluminium  engine mount, with side cooling-fins.    

Fueltank 150cc
Splash basin on tank top, self centering fuel tank seal, The fuel tank seal is angled to self guide its way into the bore of the tank. At the same time will provide a seal on the chamfered and flat edges of the seal, providing consistent engine performance from one pit stop to the next.  Built in tank splash guard which helps prevent fuel from splashing onto your air filter in the event of an overly excited pit man.

Fueline and stoppers
Kit included topqualiity soft silicone fuelline to connect to tank, car and pipe, and also includes small composite stoppers to close yr fuelline when taking out tank, engine and or pipe.

Tank with swiveling nipple and floating clunk.
With the swiveling nipple you are able to adjust the angle at which you want you fuel line to travel. At the same time the floating clunk helps when you go upside down. The clunk by gravity will fall back into the fuel, utilizing the flexibility of the silicone fuel tubing.

Oversized Tank with adjustable volume.
With the insertion of a simple screw and volume reducer you can have ROAR, IFMAR and any other organizations legal tank volume.

Low profile air filter
Centralized air filter design to minimize cab width and height. Flexible rubber boot combined with strong nylon case to support the foam elements.   Excellent dense foam airfilter elements to keep your engines clean inside.

Body
Serpent Truck body , with film and masking tape is included in the kit.

Rear wing:
Low version strong rear white aero rear wing is included for great downforce and straight line stability.

Oils and grease   
The shock-oil, diff oil and some grease is supplied to meet the standard set-up.    
   
Manual and set-up   
Full color manual with easy to follow assembly steps, exploded views for easy spares ordering, a blank and standard set-up sheet for a good start set-up.    
   
Decals   
Black and white promo body-decals ; Serpent generic and Cobra ones.    
   
Packing   
Parts are packed according to the  steps explained in the manual.    
   
Service and Support    
The Serpent distributor, dealer or agent is your source for more info, but also the Serpent website and  the member section and the Youtube channel provides lots of information.   
   
   
Needed to complete the car:   
-   radio, receiver, servo x 2
-   .21 or larger gaspowered engine and pipe-set
-    fuel with 16% or 25% nitro and fuelbottle
-   wheels and tyres    
-   tools
-   paint
-   starterbox, glowstarter
-   charging equipment